Euchner EKS FSA with Ethernet Interface Bedienungsanleitung

Electronic-Key-System Manual Electronic-Key Adapter EKS and EKS FSA with Ethernet Interface Order No. 100 420 Ethernet

Manual EKS Electronic-Key Adapter Ethernet For operation, the Electronic-Key is inserted in the Electronic-Key adapter and is held in place by a spri

Manual EKS Electronic-Key Adapter Ethernet 4 Technical data 4.1 Dimension drawing of Electronic-Key adapter For installation in a control panel yo

Manual EKS Electronic-Key Adapter Ethernet 4.2 Technical data of Electronic-Key adapter Attention! All the electrical connections must either be i

Manual EKS Electronic-Key Adapter Ethernet 4.3 Connector configuration 4.3.1 Connection socket for Ethernet interface The connection on the Electro

Manual EKS Electronic-Key Adapter Ethernet 4.4 DIP switch settings The device has three DIP switches (S1, S2, S3). DIP switch Function S1 (4-fold)

Manual EKS Electronic-Key Adapter Ethernet 4.4.3 DIP switch S3 Function S3.1 S3.2 S3.3 S3.4 Fixed IP address OFF OFF Default IP address 192.

Manual EKS Electronic-Key Adapter Ethernet 5 Mounting Mounting must be performed only by authorized personnel. Warning! Warning! To achieve the d

Manual EKS Electronic-Key Adapter Ethernet 6 Electrical connection Electrical connection may only be performed by authorized personnel trained in

Manual EKS Electronic-Key Adapter Ethernet 6.1.1 Ethernet configuration The Electronic-Key adapter can be configured for the following operating mod

Manual EKS Electronic-Key Adapter Ethernet 6.1.1.2 Dynamic IP address In this operating mode, the Electronic-Key adapter is a DHCP client. The IP ad

Manual EKS Electronic-Key Adapter Ethernet Table of contents 1 General notes...

Manual EKS Electronic-Key Adapter Ethernet 6.2 Connection of power supply (For information on pin assignment see section 4.3.2 Plug-in screw termin

Manual EKS Electronic-Key Adapter Ethernet 6.4.1 Connection example with enabling switch Figure 3: Principle of operation (illustration with selecte

Manual EKS Electronic-Key Adapter Ethernet The switching contact LA1/LA2, in series with a switching contact on the enabling switch, is connected to

Manual EKS Electronic-Key Adapter Ethernet 6.4.1.4 Circuit diagram Figure 4: Circuit diagram with enabling switch 100420-02-01/09 Subject to techni

Manual EKS Electronic-Key Adapter Ethernet 6.4.2 Connection example without enabling switch Figure 5: Principle of operation (illustration with sele

Manual EKS Electronic-Key Adapter Ethernet The safety relay is de-energized without a time delay (stop category 0) and the machine movement is stoppe

Manual EKS Electronic-Key Adapter Ethernet 6.4.2.4 Circuit diagram Figure 6: Circuit diagram without enabling switch Page 26/40 Subject to technica

Manual EKS Electronic-Key Adapter Ethernet 7 Setup Perform setup in the following sequence: 1. Set the DIP switches on the Electronic-Key adapter

Manual EKS Electronic-Key Adapter Ethernet Adapting network settings 1. Select Network Connections in your operating system. 2. Right-click Local Ar

Manual EKS Electronic-Key Adapter Ethernet 4. Click Install. The Select network component type dialog box opens. Click Protocol and then click the Ad

Manual EKS Electronic-Key Adapter Ethernet 6.4 Connection of the switched outputs (for EKS FSA only) ...

Manual EKS Electronic-Key Adapter Ethernet 7.2 Configuring the Electronic-Key adapter via the web interface The Electronic-Key adapter can be config

Manual EKS Electronic-Key Adapter Ethernet 2. Click Configuration. f The Configuration screen of the EKS web interface is now displayed. 1. Enter

Manual EKS Electronic-Key Adapter Ethernet 7.3 Reading key data using the web interface It is possible to view the serial number of the key and all

Manual EKS Electronic-Key Adapter Ethernet 8 Data transfer via the Ethernet interface 8.1 Communication This section primarily describes communicat

Manual EKS Electronic-Key Adapter Ethernet 8.3 Commands for writing and reading a read/write Electronic-Key Write and read processes are always init

Manual EKS Electronic-Key Adapter Ethernet 8.3.1 Write process Information! When this command is used, the Electronic-Key must be in the Electronic

Manual EKS Electronic-Key Adapter Ethernet 8.3.2 Read process Command message (message core, PC/PLC (control system) → EKS, see Figure 10): f TL

Manual EKS Electronic-Key Adapter Ethernet 8.3.3 Reading the serial number The Electronic-Key read/write contains a unique 8-byte serial number. Thi

Manual EKS Electronic-Key Adapter Ethernet 8.4 Command overview Description Command message Reply message Program (write) Electronic-Key TP (see s

Manual EKS Electronic-Key Adapter Ethernet 9 Exclusion of liability Exclusion of liability under the following conditions: f if the device is not u

Manual EKS Electronic-Key Adapter Ethernet 1 General notes 1.1 Use of the manual This manual describes the technical features and the function of t

Manual EKS Electronic-Key Adapter Ethernet Microsoft Windows® and ActiveX® are registered trademarks of Microsoft Corporation EUCHNER GmbH + Co. KG

Manual EKS Electronic-Key Adapter Ethernet 1.1.2 Abbreviations The following abbreviations are used in this manual: f DHCP Dynamic Host Configurat

Manual EKS Electronic-Key Adapter Ethernet 1.4 Correct use As part of a higher-level overall system, the EKS Electronic-Key adapter is used for acc

Manual EKS Electronic-Key Adapter Ethernet The Electronic-Key adapter must only be employed and used in accordance f with this manual and f other

Manual EKS Electronic-Key Adapter Ethernet 2 Safety precautions The EKS Electronic-Key adapter is not a safety component in the sense of the machin

Manual EKS Electronic-Key Adapter Ethernet 3 Function 3.1 Functional description 3.1.1 Common functions of EKS standard and version EKS FSA The EK