Euchner RPS Bedienungsanleitung PDF herunterladen

Operating Instructions for Rope Pull Switches

RPS...

Safety rope pull switch RPS

Correct use

In accordance with EN 60947-5-5, EN ISO 13850, it must be ensured that parts of or complete industrial

machines or installations can be stopped as quickly as possible by generation of an emergency stop signal.

The purpose of these regulations is to prevent any danger for persons or damage to machines.

The following applicable standards must be taken into account for this purpose:

Regulations on installation and operation: EN ISO 13849-1 Safety of machinery. Safety related parts of

control systems

Risk assessment on the machine: EN ISO 12100, Safety of machinery – Basic concepts –

General principles for design – Risk assessment and risk

reduction.

The safety rope pull switches of the series RPS have been designed and tested in accordance with the

standards EN 60947-5-5 and EN ISO 13850. They must be used only in control circuits.

Safety rope pull switches are used on the accessible sides of conveyor systems or machines. In contrast to

emergency stop switches (e.g. mushroom-head pushbuttons) located at certain intervals that allow the

emergency stop signal to be generated only at the devices themselves, rope pull switches allow signal

generation at any point along the rope length.

The safety rope pull switches of the type RPS are intended for use only in closed areas.

Design

The safety rope pull switches of the type RPS consist of a polyamide housing, those of the type RPS-M of a

die-cast aluminum housing. They achieve the specified degree of protection IP67 if the cover is properly closed

and if a cable gland is used that offers at least equivalent protection. The RPS has three cable entries M20x1.5.

The switches comply with the international requirements according to EN 60947-5-5 and EN ISO 13850, i.e.

after actuation or a rope tear, the emergency stop switch latches automatically, and the switch can then be

reset to its initial state only by means of the resetting device on the switch.

Depending on the switch version, it is possible to achieve a rope length of 75 m. It must be taken into account

here that the friction in the overall system can become so high due to the rope guides that this makes it difficult

or impossible to reset the system (see section Installation).

This can be avoided by choosing different system components.

The user is responsible for ensuring that the system functions properly.

1 2 3 4 5 6 ... 15 16

Inhaltsverzeichnis

Seite 1 - Correct use

Operating Instructions for Rope Pull Switches RPS... Safety rope pull switch RPS Correct use In accordance with EN 60947-5-5, EN ISO 13850, i

Seite 2 - Safety precautions

Operating Instructions for Rope Pull Switches RPS... Electrical connection Electrical connection must be performed only by authorized personnel. Co

Seite 3 - RPS-M-E-3131-SC-300M

Operating Instructions for Rope Pull Switches RPS... 11Connection example The following connection example shows a possible circuit structure with re

Seite 4 - Dimensions

Operating Instructions for Rope Pull Switches RPS... Technical data Version RPS… RPS-M… Electrical data (refers to the switch without plug connec

Seite 5

Operating Instructions for Rope Pull Switches RPS... 13 Switching elements The values for the tensile force depend on the switch type used. (RPS...10

Seite 6 - Table 1

Operating Instructions for Rope Pull Switches RPS... 14 Accessories Designation Description/version Packaging unit Order no./item Eyebolt Thread

Seite 7

Operating Instructions for Rope Pull Switches RPS... 15

Seite 8 - Installation sequence

Euchner GmbH + Co. KG Kohlhammerstraße 16 D-70771 Leinfelden-Echterdingen [email protected] www.euchner.de Edition: 090276-06-08/12 Title: Operati

Seite 9

Operating Instructions for Rope Pull Switches RPS... Function The system consists of the switching device, a red pull rope, supports and a counters

Seite 10 - Electrical connection

Operating Instructions for Rope Pull Switches RPS... 3 Improper installation or manipulation of the rope pull switch will lead to loss of the person

Seite 11 - Switches RPS

Operating Instructions for Rope Pull Switches RPS... Dimensions RPS...PR... RPS...PC... RPS...SC... RPS-M...SC... All dimensions in millimeter

Seite 12 - Technical data

Operating Instructions for Rope Pull Switches RPS... 5 Mounting Note Under ideal installation conditions it is possible to achieve a maximum rope t

Seite 13

Operating Instructions for Rope Pull Switches RPS... Selection of system components A tensioner spring must be installed on the thrust bearing in or

Seite 14 - Accessories

Operating Instructions for Rope Pull Switches RPS... 7 When installing and adjusting the rope pull switch, it is necessary to take into account the p

Seite 15

Operating Instructions for Rope Pull Switches RPS... Installation sequence Installation must be performed only by authorized personnel. 1 A 1.1A 1

Seite 16

Operating Instructions for Rope Pull Switches RPS... 9 4 A Connect pull rope fast-action clamping head (see Item 1). Pre-tension pull rope. B Con

Weitere Dokumente für Sicherheit Euchner RPS

Um das Dokument anzuzeigen Euchner RPS Bedienungsanleitung

Euchner RPS Bedienungsanleitung (16 Seiten)

Kommentare zu diesen Handbüchern

Keine Kommentare

Euchner RPS Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Sicherheit Euchner RPS herunter. EUCHNER RPS User Manual Benutzerhandbuch

Inhaltsverzeichnis

Weitere Dokumente für Sicherheit Euchner RPS

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheit Euchner RPS